TRENCH DRAINS <If scheduled delete this section however you may want to use this information in your
schedule>:
Trench Drain Supply has developed the following paragraphs to assist the design professional in specifying trench
drains. Insert these paragraphs into appropriate project specification sections or schedule them.
This notes is included to assist the design professional in editing the specifications to suit project requirements, and is
not intended to be included in the final specification.
For assistance on the selection of the products in this section or for other questions, contact Trench Drain Supply at
1-877-903-7246 or by email at . Website is www.trenchdrainsupply.com
1Meter = 39.3701 inches.
Insert the following paragraph under “Submittals”:
A. Review Submittals:
1. Product Data: Manufacturer’s standard data sheets describing components including materials,
dimensions, relationship to adjacent construction, and attachments.
PART 2- Products
1.1 Walkway drain
A. TD-1 CPS100-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 6 inch nominal width trench drain shall be provided with 4" internal channel width
and radiused bottom. Interconnecting sections shall be made of sheet molding compound/glass reinforced
polyester material. Provide support brackets capable of accepting rebar, end outlets, bottom outlets, end
caps, and corner/tee connectors shall be available. Channel grates shall be as specified.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Flat][Presloped].
3. Installation Brackets: [Yes][No].
4. Grate shall be Galvanized Steel, Slotted “A” class Grate with special Locks.
5. Drain shall include:
a. One End Cap with 4" Outlet
b. Two Solid End Caps.
c. One Bottom Outlet
B. TD-2 CPS106-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 6 inch nominal width trench drain shall be provided with 4" internal channel width
and radiused bottom. Interconnecting sections shall be made of sheet molding compound/glass reinforced
polyester material. Provide support brackets capable of accepting rebar, end outlets, bottom outlets, end
caps, and corner/tee connectors shall be available. Channel grates shall be as specified.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply # indicated.
2. Fall: [Flat][Presloped].
3. Installation Brackets: [Yes][No].
4. Grate shall be Galvanized Steel Slotted “A” class Grate with special Locks.
5. Drain shall include:
a. One End Cap with 4" Outlet
b. Two Solid End Caps.
c. One Bottom Outlet
C. TD-3 CPS303-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 4” Nominal width complete fiberglass channel system. Channel available without
fall. 4" bottom or 3" endplate outlet connection.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: Flat.
3. Installation Brackets: [Yes][No].
4. Grate shall be Galvanized Slotted “A” class Grate with standard locks.
5. Drain shall include:
a. Galvanized locks
b. End Caps doubling as outlets
c. One Bottom Outlet
d. Dirt grate that fits outlet
1.2 Walkway drain (ADA Compliant)
A. TD-4 CPS100-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 6 inch nominal width trench drain shall be provided with 4" internal channel width
and radiused bottom. Interconnecting sections shall be made of sheet molding compound/glass reinforced
polyester material. Provide support brackets capable of accepting rebar, end outlets, bottom outlets, end
caps, and corner/tee connectors shall be available. Channel grates shall be as specified.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Flat][Presloped].
3. Installation Brackets: [Yes][No].
4. Grate shall be Galvanized Perforated “A” class with special Locks.
5. Drain shall include:
a. One End Cap with 4" Outlet
b. Two Solid End Caps.
c. One Bottom Outlet
B. TD-5 CPS106-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 6 inch nominal width trench drain shall be provided with 4" internal channel width
and radiused bottom. Interconnecting sections shall be made of sheet molding compound/glass reinforced
polyester material. Provide support brackets capable of accepting rebar, end outlets, bottom outlets, end
caps, and corner/tee connectors shall be available. Channel grates shall be as specified.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Flat][Presloped].
3. Installation Brackets: [Yes][No].
4. Grate shall be Galvanized Perforated “A” class with special Locks.
5. Drain shall include:
a. One End Cap with 4" Outlet
b. Two Solid End Caps.
c. One Bottom Outlet
C. TD-6 CPS303-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 4” Nominal width complete fiberglass channel system. Channel available without
fall. 4" bottom or 3" endplate outlet connection.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: Flat.
3. Installation Brackets: [Yes][No].
4. Grate shall be Galvanized perforated “A” class, ADA compliant, with standard locks.
5. Drain shall include:
a. Galvanized locks
b. End Caps doubling as outlets
c. One Bottom Outlet
d. Dirt grate that fits outlet
1.3 Pool (ADA Compliant)
A. TD-7 CPS100-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 6 inch nominal width trench drain shall be provided with 4" internal channel width
and radiused bottom. Interconnecting sections shall be made of sheet molding compound/glass reinforced
polyester material. Provide support brackets capable of accepting rebar, end outlets, bottom outlets, end
caps, and corner/tee connectors shall be available. Channel grates shall be as specified.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Flat][Presloped].
3. Installation Brackets: [Yes][No].
4. Grate shall be HDPE Perforated “A” class with special Locks.
5. Drain shall include:
a. One End Cap with 4" Outlet
b. Two Solid End Caps.
c. One Bottom Outlet
B. TD-8 CPS106-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 6 inch nominal width trench drain shall be provided with 4" internal channel width
and radiused bottom. Interconnecting sections shall be made of sheet molding compound/glass reinforced
polyester material. Provide support brackets capable of accepting rebar, end outlets, bottom outlets, end
caps, and corner/tee connectors shall be available. Channel grates shall be as specified.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Flat][Presloped].
3. Installation Brackets: [Yes][No].
4. Grate shall be HDPE Perforated “A” class with special Locks.
5. Drain shall include:
a. One End Cap with 4" Outlet
b. Two Solid End Caps.
c. One Bottom Outlet
1.4 Promenade
A. TD-9 CPS100-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 6 inch nominal width trench drain shall be provided with 4" internal channel width
and radiused bottom. Interconnecting sections shall be made of sheet molding compound/glass reinforced
polyester material. Provide support brackets capable of accepting rebar, end outlets, bottom outlets, end
caps, and corner/tee connectors shall be available. Channel grates shall be as specified.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Flat][Presloped].
3. Installation Brackets: [Yes][No].
4. Grate shall be Galvanized Reinforced Mesh, “B” class with special Locks.
5. Drain shall include:
a. One End Cap with 4" Outlet
b. Two Solid End Caps.
c. One Bottom Outlet
B. TD-10 CPS106-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 6 inch nominal width trench drain shall be provided with 4" internal channel width
and radiused bottom. Interconnecting sections shall be made of sheet molding compound/glass reinforced
polyester material. Provide support brackets capable of accepting rebar, end outlets, bottom outlets, end
caps, and corner/tee connectors shall be available. Channel grates shall be as specified.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Flat][Presloped].
3. Installation Brackets: [Yes][No].
4. Grate shall be Galvanized Reinforced Mesh, “B” class with special Locks.
5. Drain shall include:
a. One End Cap with 4" Outlet
b. Two Solid End Caps.
c. One Bottom Outlet
C. TD-11 CPS303-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 4” Nominal width complete fiberglass channel system. Channel available without
fall. Bottom or endplate outlet connection.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: Flat.
3. Installation Brackets: [Yes][No].
4. Grate shall be Galvanized mesh “B” class, with standard locks.
5. Drain shall include:
a. Galvanized locks
b. End Caps doubling as outlets
c. One Bottom Outlet
d. Dirt grate that fits outlet
1.5 Chemically Resistant
A. TD-12 CPS100-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 6 inch nominal width trench drain shall be provided with 4" internal channel width
and radiused bottom. Interconnecting sections shall be made of sheet molding compound/glass reinforced
polyester material. Provide support brackets capable of accepting rebar, end outlets, bottom outlets, end
caps, and corner/tee connectors shall be available. Channel grates shall be as specified.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Flat][Presloped].
3. Installation Brackets: [Yes][No].
4. Grate shall be Glass Filled Nylon Slotted, “C” class with special Locks.
5. Drain shall include:
a. One End Cap with 4" Outlet
b. Two Solid End Caps.
c. One Bottom Outlet
B. TD-13 CPS106-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 6 inch nominal width trench drain shall be provided with 4" internal channel width
and radiused bottom. Interconnecting sections shall be made of sheet molding compound/glass reinforced
polyester material. Provide support brackets capable of accepting rebar, end outlets, bottom outlets, end
caps, and corner/tee connectors shall be available. Channel grates shall be as specified.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Flat][Presloped].
3. Installation Brackets: [Yes][No].
4. Grate shall be Glass Filled Nylon Slotted, “C” class with special Locks.
5. Drain shall include:
a. One End Cap with 4" Outlet
b. Two Solid End Caps.
c. One Bottom Outlet
C. TD-14 CPS303-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 4” Nominal width complete fiberglass channel system. Channel available without
fall. Bottom or endplate outlet connection.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: Flat.
3. Installation Brackets: [Yes][No].
4. Grate shall be nylon filled “C” class, with standard locks.
5. Drain shall include:
a. Galvanized locks
b. End Caps doubling as outlets
c. One Bottom Outlet
d. Dirt grate that fits outlet
6. All hardware needed shall be included.
1.6 Garage/Driveway Drain (Galvanized)
A. TD-15 CPS100-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 6 inch nominal width trench drain shall be provided with 4" internal channel width
and radiused bottom. Interconnecting sections shall be made of sheet molding compound/glass reinforced
polyester material. Provide support brackets capable of accepting rebar, end outlets, bottom outlets, end
caps, and corner/tee connectors shall be available. Channel grates shall be as specified.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Flat][Presloped].
3. Installation Brackets: [Yes][No].
4. Grate shall be Reinforced Galvanized Steel, slotted, “C” class Grate with special Locks.
5. Drain shall include:
a. One End Cap with 4" Outlet
b. Two Solid End Caps.
c. One Bottom Outlet
B. TD-16 CPS106-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 6 inch nominal width trench drain shall be provided with 4" internal channel width
and radiused bottom. Interconnecting sections shall be made of sheet molding compound/glass reinforced
polyester material. Provide support brackets capable of accepting rebar, end outlets, bottom outlets, end
caps, and corner/tee connectors shall be available. Channel grates shall be as specified.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Flat][Presloped].
3. Installation Brackets: [Yes][No].
4. Grate shall be Reinforced Galvanized Steel, slotted, “C” class Grate with special Locks.
5. Drain shall include:
a. One End Cap with 4" Outlet
b. Two Solid End Caps.
c. One Bottom Outlet
1.7 Garage/Driveway Drain (Ductile Iron)
A. TD-17 CPS100-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 6 inch nominal width trench drain shall be provided with 4" internal channel width
and radiused bottom. Interconnecting sections shall be made of sheet molding compound/glass reinforced
polyester material. Provide support brackets capable of accepting rebar, end outlets, bottom outlets, end
caps, and corner/tee connectors shall be available. Channel grates shall be as specified.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Flat][Presloped].
3. Installation Brackets: [Yes][No].
4. Grate shall be Ductile Iron Slotted, “C” class Grate with standard locks.
5. Drain shall include:
a. One End Cap with 4" Outlet
b. Two Solid End Caps.
c. One Bottom Outlet
B. TD-18 CPS100HD-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80,
83, 86, 90, 93, 96, 99] [FT]: 6 inch nominal width heavy duty trench drain with frame shall be provided
with 4" internal channel width and radiused bottom. Interconnecting sections shall be made of sheet
molding compound/glass reinforced polyester material. Provide support brackets capable of accepting
rebar, end outlets, bottom outlets, end caps, and corner/tee connectors shall be available. Channel grates
shall be as specified.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Flat][Presloped].
3. Installation Brackets: [Yes][No].
4. Grate shall be Ductile Iron Slotted, “C” class Grate with special locks.
5. Drain shall include:
a. One End Cap with 4" Outlet
b. Two Solid End Caps.
c. One Bottom Outlet
C. TD-19 CPS106-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 6 inch nominal width trench drain shall be provided with 4" internal channel width
and radiused bottom. Interconnecting sections shall be made of sheet molding compound/glass reinforced
polyester material. Provide support brackets capable of accepting rebar, end outlets, bottom outlets, end
caps, and corner/tee connectors shall be available. Channel grates shall be as specified.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Flat][Presloped].
3. Installation Brackets: [Yes][No].
4. Grate shall be Ductile Iron Slotted, “C” class Grate with special locks.
5. Drain shall include:
a. One End Cap with 4" Outlet
b. Two Solid End Caps.
c. One Bottom Outlet
D. TD-20 CPS303-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 4” Nominal width complete fiberglass channel system. Channel available without
fall. Bottom or endplate outlet connection.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: Flat.
3. Installation Brackets: [Yes][No].
4. Grate shall be ductile iron “C” class, with standard locks.
5. Drain shall include:
a. Galvanized locks
b. End Caps doubling as outlets
c. One Bottom Outlet
d. Dirt grate that fits outlet
6. All hardware needed shall be included.
1.8 Garage/Driveway Drain (ADA Ductile Iron)
A. TD-21 CPS100HD-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80,
83, 86, 90, 93, 96, 99] [FT]: 6 inch nominal width heavy dutytrench drain with frame shall be provided
with 4" internal channel width and radiused bottom. Interconnecting sections shall be made of sheet
molding compound/glass reinforced polyester material. Provide support brackets capable of accepting
rebar, end outlets, bottom outlets, end caps, and corner/tee connectors shall be available. Channel grates
shall be as specified.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Flat][Presloped].
3. Installation Brackets: [Yes][No].
4. Grate shall be Ductile Iron Slim Slotted, “C” class ADA compliant Grate with standard locks.
5. Drain shall include:
a. One End Cap with 4" Outlet
b. Two Solid End Caps.
c. One Bottom Outlet
B. TD-22 CPS100HD-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80,
83, 86, 90, 93, 96, 99] [FT]: 6 inch nominal width heavy dutytrench drain with frame shall be provided
with 4" internal channel width and radiused bottom. Interconnecting sections shall be made of sheet
molding compound/glass reinforced polyester material. Provide support brackets capable of accepting
rebar, end outlets, bottom outlets, end caps, and corner/tee connectors shall be available. Channel grates
shall be as specified.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Flat][Presloped].
3. Installation Brackets: [Yes][No].
4. Grate shall be Ductile Iron Longitudinal Slotted, “C” class ADA compliant Grate with standard
locks.
5. Drain shall include:
a. One End Cap with 4" Outlet
b. Two Solid End Caps.
c. One Bottom Outlet
C. TD-23 CPS100HD-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80,
83, 86, 90, 93, 96, 99] [FT]: 6 inch nominal width heavy dutytrench drain with frame shall be provided
with 4" internal channel width and radiused bottom. Interconnecting sections shall be made of sheet
molding compound/glass reinforced polyester material. Provide support brackets capable of accepting
rebar, end outlets, bottom outlets, end caps, and corner/tee connectors shall be available. Channel grates
shall be as specified.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Flat][Presloped].
3. Installation Brackets: [Yes][No].
4. Grate shall be Ductile Iron Slim Slotted, “E” class ADA compliant Grate with standard locks.
5. Drain shall include:
a. One End Cap with 4" Outlet
b. Two Solid End Caps.
c. One Bottom Outlet
D. TD-24 CPS303-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 4” Nominal width complete fiberglass channel system. Channel available without
fall. Bottom or endplate outlet connection.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: Flat.
3. Installation Brackets: [Yes][No].
4. Grate shall be ductile iron “C” class, ADA compliant with standard locks.
5. Drain shall include:
a. Galvanized locks
b. End Caps doubling as outlets
c. One Bottom Outlet
d. Dirt grate that fits outlet
1.9 6” Wide Trench Drain with E Class, Ductile Iron Grate
A. TD-25 CPS100HD-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80,
83, 86, 90, 93, 96, 99] [FT]: 6 inch nominal width heavy duty trench drain with frame shall be provided
with 4" internal channel width and radiused bottom. Interconnecting sections shall be made of sheet
molding compound/glass reinforced polyester material. Provide support brackets capable of accepting
rebar, end outlets, bottom outlets, end caps, and corner/tee connectors shall be available. Channel grates
shall be as specified.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Flat][Presloped].
3. Installation Brackets: [Yes][No].
4. Grate shall be Ductile Iron Slotted, “E” class with standard locks.
5. Drain shall include:
a. One End Cap with 4" Outlet
b. Two Solid End Caps.
c. One Bottom Outlet
1.10 8” Wide Trench Drain with A Class, Galvanized, Mesh Grate
A. TD-26 CPS200-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 10 inch nominal width trench drain shall be 39.4" long with 8" internal channel
width and radiused bottom. Interconnecting sections shall be made of SMC/GRP (sheet molding compound
/ glass reinforced polyester) material and available with and without slope. Support brackets capable of
accepting rebar, end outlets, bottom outlets, end caps, and corner/tee connectors shall be available. Grate
shall be equipped with special locking device. Ductile iron frame or stainless steel veneer rails to protect
channel edges are available.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-Sloped][Flat].
3. Installation Brackets: [Yes][No].
4. Grate shall be A Class, Galvanized, Mesh with standard locks.
5. Drain shall include:
a. End Cap with 6” outlet.
b. Two solid End Caps.
c. One Bottom Outlet.
1.11 8” Wide Trench Drain with C Class, Ductile Iron, Slotted Grate
A. TD-27 CPS200-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 10 inch nominal width trench drain shall be 39.4" long with 8" internal channel
width and radiused bottom. Interconnecting sections shall be made of SMC/GRP (sheet molding compound
/ glass reinforced polyester) material and available with and without slope. Support brackets capable of
accepting rebar, end outlets, bottom outlets, end caps, and corner/tee connectors shall be available. Grate
shall be equipped with special locking device. Ductile iron frame or stainless steel veneer rails to protect
channel edges are available.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-Sloped][Flat].
3. Installation Brackets: [Yes][No].
4. Grate shall be C Class, Ductile Iron, Slotted with special locks.
5. Drain shall include:
a. End Cap with 6” outlet.
b. Two solid End Caps.
c. One Bottom Outlet.
1.12 8” Wide Trench Drain with C Class, Reinforced, Mesh Grate
A. TD-28 CPS200-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 10 inch nominal width trench drain shall be 39.4" long with 8" internal channel
width and radiused bottom. Interconnecting sections shall be made of SMC/GRP (sheet molding compound
/ glass reinforced polyester) material and available with and without slope. Support brackets capable of
accepting rebar, end outlets, bottom outlets, end caps, and corner/tee connectors shall be available. Grate
shall be equipped with special locking device. Ductile iron frame or stainless steel veneer rails to protect
channel edges are available.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-Sloped][Flat].
3. Installation Brackets: [Yes][No].
4. Grate shall be C Class, Reinforced, Mesh with special locks.
5. Drain shall include:
a. End Cap with 6” outlet.
b. Two solid End Caps.
c. One Bottom Outlet.
1.13 8” Wide Trench Drain with C Class, Ductile Iron, Slotted Grate
A. TD-29 CPS200HD-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80,
83, 86, 90, 93, 96, 99] [FT]: 10 inch nominal width trench drain with frame shall be 39.4" long with 8"
internal channel width and radiused bottom. Interconnecting sections shall be made of SMC/GRP (sheet
molding compound / glass reinforced polyester) material and available with and without slope. Support
brackets capable of accepting rebar, end outlets, bottom outlets, end caps, and corner/tee connectors shall
be available. Grate shall be equipped with special locking device. Ductile iron frame or stainless steel
veneer rails to protect channel edges are available.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-Sloped][Flat].
3. Installation Brackets: [Yes][No].
4. Grate shall be C Class, Ductile Iron, Slotted with special locks.
5. Drain shall include:
a. End Cap with 6” outlet.
b. Two solid End Caps.
c. One Bottom Outlet.
1.14 8” Wide Trench Drain with D Class, Ductile Iron, Slotted Grate
A. TD-30 CPS200-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 10 inch nominal width trench drain shall be 39.4" long with 8" internal channel
width and radiused bottom. Interconnecting sections shall be made of SMC/GRP (sheet molding compound
/ glass reinforced polyester) material and available with and without slope. Support brackets capable of
accepting rebar, end outlets, bottom outlets, end caps, and corner/tee connectors shall be available. Grate
shall be equipped with special locking device. Ductile iron frame or stainless steel veneer rails to protect
channel edges are available.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-Sloped][Flat].
3. Installation Brackets: [Yes][No].
4. Grate shall be D Class, Ductile Iron, Slotted with special locks.
5. Drain shall include:
a. End Cap with 6” outlet.
b. Two solid End Caps.
c. One Bottom Outlet.
1.15 8” Wide Trench Drain with E Class, Ductile Iron, Slotted Grate
A. TD-31 CPS200-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 10 inch nominal width trench drain shall be 39.4" long with 8" internal channel
width and radiused bottom. Interconnecting sections shall be made of SMC/GRP (sheet molding compound
/ glass reinforced polyester) material and available with and without slope. Support brackets capable of
accepting rebar, end outlets, bottom outlets, end caps, and corner/tee connectors shall be available. Grate
shall be equipped with special locking device. Ductile iron frame or stainless steel veneer rails to protect
channel edges are available.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-Sloped][Flat].
3. Installation Brackets: [Yes][No].
4. Grate shall be E Class, Ductile Iron, Slotted, with special locks.
5. Drain shall include:
a. End Cap with 6” outlet.
b. Two solid End Caps.
c. One Bottom Outlet.
1.16 8” Wide Trench Drain with E Class, Wave Mesh Grate
A. TD-32 CPS200HD-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80,
83, 86, 90, 93, 96, 99] [FT]: 10 inch nominal width trench drain with frame shall be 39.4" long with 8"
internal channel width and radiused bottom. Interconnecting sections shall be made of SMC/GRP (sheet
molding compound / glass reinforced polyester) material and available with and without slope. Support
brackets capable of accepting rebar, end outlets, bottom outlets, end caps, and corner/tee connectors shall
be available. Grate shall be equipped with special locking device. Ductile iron frame or stainless steel
veneer rails to protect channel edges are available.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-Sloped][Flat].
3. Installation Brackets: [Yes][No].
4. Grate shall be E Class, Wave Mesh, with special locks.
5. Drain shall include:
a. End Cap with 6” outlet.
b. Two solid End Caps.
c. One Bottom Outlet.
1.17 8” Wide Trench Drain with E Class, ADA compliant, ductile iron grate.
A. TD-33 CPS200HD-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80,
83, 86, 90, 93, 96, 99] [FT]: 10 inch nominal width trench drain with frame shall be 39.4" long with 8"
internal channel width and radiused bottom. Interconnecting sections shall be made of SMC/GRP (sheet
molding compound / glass reinforced polyester) material and available with and without slope. Support
brackets capable of accepting rebar, end outlets, bottom outlets, end caps, and corner/tee connectors shall
be available. Grate shall be equipped with special locking device. Ductile iron frame or stainless steel
veneer rails to protect channel edges are available.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-Sloped][Flat].
3. Installation Brackets: [Yes][No].
4. Grate shall be E Class, ADA compliant, ductile iron, with special locks.
5. Drain shall include:
a. End Cap with 6” outlet.
b. Two solid End Caps.
c. One Bottom Outlet.
1.18 8” Wide Trench Drain with D Class, ductile iron, solid, cover.
A. TD-34 CPS200HD-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80,
83, 86, 90, 93, 96, 99] [FT]: 10 inch nominal width trench drain with frame shall be 39.4" long with 8"
internal channel width and radiused bottom. Interconnecting sections shall be made of SMC/GRP (sheet
molding compound / glass reinforced polyester) material and available with and without slope. Support
brackets capable of accepting rebar, end outlets, bottom outlets, end caps, and corner/tee connectors shall
be available. Grate shall be equipped with special locking device. Ductile iron frame or stainless steel
veneer rails to protect channel edges are available.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-Sloped][Flat].
3. Installation Brackets: [Yes][No].
4. Grate shall be D Class, ductile iron, solid, with special locks.
5. Drain shall include:
a. End Cap with 6” outlet.
b. Two solid End Caps.
c. One Bottom Outlet.
1.19 8” Wide Trench Drain with A Class, Vinylester, Bar Grate
A. TD-35 CPS200-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 10 inch nominal width trench drain shall be 39.4" long with 8" internal channel
width and radiused bottom. Interconnecting sections shall be made of SMC/GRP (sheet molding compound
/ glass reinforced polyester) material and available with and without slope. Support brackets capable of
accepting rebar, end outlets, bottom outlets, end caps, and corner/tee connectors shall be available. Grate
shall be equipped with special locking device. Ductile iron frame or stainless steel veneer rails to protect
channel edges are available.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-Sloped][Flat].
3. Installation Brackets: [Yes][No].
4. Grate shall be A Class, fiberglass Vinylester bar, with standards locks.
5. Drain shall include:
a. End Cap with 6” outlet.
b. Two solid End Caps.
c. One Bottom Outlet.
1.20 12” Wide Trench Drain with C Class, Ductile Iron Wave Grate
A. TD-36 CPS300-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 14 inch nominal wide trench drain shall be 39.4" long with 12" internal channel
width. Interconnecting channel sections shall be made of SMC/GRP (sheet molding compound/glass
reinforced polyester) material and available with and without slope. Channel support brackets capable of
accepting rebar, end outlets, bottom outlets, end caps, and corner/tee connectors shall be available. Special
or locking bolt securing devices and ductile iron rails or stainless steel veneer edges to protect channel
edges are available.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-Sloped][Flat].
3. Installation Brackets: [Yes][No].
4. Grate shall be C Class, Ductile Iron, wave, with special locks.
5. Drain shall include:
a. End Cap with 6” outlet.
b. Two solid End Caps.
c. One Bottom Outlet.
1.21 12” Wide Trench Drain with A Class, Vinylester Grate
A. TD-37 CPS300-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 14 inch nominal wide trench drain shall be 39.4" long with 12" internal channel
width. Interconnecting channel sections shall be made of SMC/GRP (sheet molding compound/glass
reinforced polyester) material and available with and without slope. Channel support brackets capable of
accepting rebar, end outlets, bottom outlets, end caps, and corner/tee connectors shall be available. Special
or locking bolt securing devices and ductile iron rails or stainless steel veneer edges to protect channel
edges are available..
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-Sloped][Flat].
3. Installation Brackets: [Yes][No].
4. Grate shall be A Class, fiberglass vinylester, with standard locks.
5. Drain shall include:
a. End Cap with 6” outlet.
b. Two solid End Caps.
c. One Bottom Outlet.
1.22 12” Wide Trench Drain with C Class, Reinforced Steel Mesh Grate
A. TD-38 CPS300-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 14 inch nominal wide trench drain shall be 39.4" long with 12" internal channel
width. Interconnecting channel sections shall be made of SMC/GRP (sheet molding compound/glass
reinforced polyester) material and available with and without slope. Channel support brackets capable of
accepting rebar, end outlets, bottom outlets, end caps, and corner/tee connectors shall be available. Special
or locking bolt securing devices and ductile iron rails or stainless steel veneer edges to protect channel
edges are available.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-Sloped][Flat].
3. Installation Brackets: [Yes][No].
4. Grate shall be C Class, reinforced steel mesh, with special locks.
5. Drain shall include:
a. End Cap with 6” outlet.
b. Two solid End Caps.
c. One Bottom Outlet.
1.23 12” Wide Trench Drain with D Class, Ductile Iron Wave Grate
A. TD-39 CPS300-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT14 inch nominal wide trench drain shall be 39.4" long with 12" internal channel
width. Interconnecting channel sections shall be made of SMC/GRP (sheet molding compound/glass
reinforced polyester) material and available with and without slope. Channel support brackets capable of
accepting rebar, end outlets, bottom outlets, end caps, and corner/tee connectors shall be available. Special
or locking bolt securing devices and ductile iron rails or stainless steel veneer edges to protect channel
edges are available.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-Sloped][Flat].
3. Installation Brackets: [Yes][No].
4. Grate shall be D Class, ductile iron wave, with special locks.
5. Drain shall include:
a. End Cap with 6” outlet.
b. Two solid End Caps.
c. One Bottom Outlet.
1.24 12” Wide Trench Drain with E Class, Ductile Iron Wave Grate
A. TD-40 CPS300-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 14 inch nominal wide trench drain shall be 39.4" long with 12" internal channel
width. Interconnecting channel sections shall be made of SMC/GRP (sheet molding compound/glass
reinforced polyester) material and available with and without slope. Channel support brackets capable of
accepting rebar, end outlets, bottom outlets, end caps, and corner/tee connectors shall be available. Special
or locking bolt securing devices and ductile iron rails or stainless steel veneer edges to protect channel
edges are available.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-Sloped][Flat].
3. Installation Brackets: [Yes][No].
4. Grate shall be E Class, Ductile Iron Wave, with special locks.
5. Drain shall include:
a. End Cap with 6” outlet.
b. Two solid End Caps.
c. One Bottom Outlet.
1.25 12” Wide Trench Drain with E Class, Solid Cover.
A. TD-41 CPS300-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 14 inch nominal wide trench drain shall be 39.4" long with 12" internal channel
width. Interconnecting channel sections shall be made of SMC/GRP (sheet molding compound/glass
reinforced polyester) material and available with and without slope. Channel support brackets capable of
accepting rebar, end outlets, bottom outlets, end caps, and corner/tee connectors shall be available. Special
or locking bolt securing devices and ductile iron rails or stainless steel veneer edges to protect channel
edges are available.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-Sloped][Flat].
3. Installation Brackets: [Yes][No].
4. Grate shall be E Class, Solid, with special locks.
5. Drain shall include:
a. End Cap with 6” outlet.
b. Two solid End Caps.
c. One Bottom Outlet.
1.26 4” Wide Trench Drain with A Class, Galvanized Steel, Slotted Grate.
A. TD-42 CPS504-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: Polymer channel with integrated galvanized steel edge. Available with built-in
fall, neutral or stepped fall. Special or standard locking grates.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-Sloped][Flat.][Stepped]
3. Installation Brackets: [Yes][No].
4. Grate shall be A Class, galvanized steel, slotted, with standard locks.
5. Drain shall include:
a. Standard grate hold down locks.
b. End Cap with outlet.
c. Solid End Caps.
1.27 4” Wide Trench Drain with B Class,Galvanized Steel, Mesh Grate.
A. TD-43 CPS504-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: Polymer channel with integrated galvanized steel edge. Available with built-in
fall, neutral or stepped fall. Special or standard locking grates.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-Sloped][Flat.][Stepped]
3. Installation Brackets: [Yes][No].
4. Grate shall be B Class, galvanized steel, mesh, with standard locks.
5. Drain shall include:
a. Standard grate hold down locks.
b. End Cap with outlet.
c. Solid End Caps.
1.28 4” Wide Trench Drain with C Class, Reinforced Galvanized Steel, Slotted Grate.
A. TD-44 CPS504-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: Polymer channel with integrated galvanized steel edge. Available with built-in
fall, neutral or stepped fall. Special or standard locking grates.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-Sloped][Flat.][Stepped]
3. Installation Brackets: [Yes][No].
4. Grate shall be C class, reinforced, galvanized steel slotted, with standard locks.
5. Drain shall include:
a. Standard grate hold down locks.
b. End Cap with outlet.
c. Solid End Caps.
6. All hardware needed shall be included.
1.29 4” Wide Trench Drain with ADA Compliant, C Class, Ductile Iron, Slotted Grate.
A. TD-45 CPS504-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: Polymer channel with integrated galvanized steel edge. Available with built-in
fall, neutral or stepped fall. Special or standard locking grates.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-Sloped][Flat.][Stepped]
3. Installation Brackets: [Yes][No].
4. Grate shall be ADA compliant, C class, ductile iron, slotted with standard locks.
5. Drain shall include:
a. Standard grate hold down locks.
b. End Cap with outlet.
c. Solid End Caps.
1.30 4” Wide Shallow Trench Drain with A Class, Galvanized Steel, Slotted Grate.
A. TD-46 CPS554-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: Shallow polymer channel with integrated galvanized steel edge. Available without
fall. Special or standard locking grates.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: Flat.
3. Installation Brackets: [Yes][No].
4. Grate shall be A Class, Galvanized Steel, Slotted, with standard locks.
5. Drain shall include:
a. Standard grate hold down locks.
b. End Cap with outlet.
c. Solid End Cap.
1.31 4” Wide Shallow Trench Drain with B Class, Galvanized Steel, Mesh Grate.
A. TD-47 CPS554-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: Shallow polymer channel with integrated galvanized steel edge. Available without
fall. Special or standard locking grates.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: Flat.
3. Installation Brackets: [Yes][No].
4. Grate shall be B Class, galvanized steel, mesh, with standard locks.
5. Drain shall include:
a. Standard grate hold down locks.
b. End Cap with outlet.
c. Solid End Cap.
1.32 4” Wide Shallow Trench Drain with C Class, Reinforced, Galvanized Steel, Slotted Grate.
A. TD-48 CPS554-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: Shallow polymer channel with integrated galvanized steel edge. Available without
fall. Special or standard locking grates.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: Flat.
3. Installation Brackets: [Yes][No].
4. Grate shall be C Class, reinforced, galvanized steel, slotted, with standard locks.
5. Drain shall include:
a. Standard grate hold down locks.
b. End Cap with outlet.
c. Solid End Cap.
1.33 4” Wide Shallow Trench Drain with C Class, Ductile Iron Slotted Grate.
A. TD-49 CPS554-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: Shallow polymer channel with integrated galvanized steel edge. Available without
fall. Special or standard locking grates.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: Flat.
3. Installation Brackets: [Yes][No].
4. Grate shall be C Class, Ductile Iron Slotted, with standard locks.
5. Drain shall include:
a. Standard grate hold down locks.
b. End Cap with outlet.
c. Solid End Cap.
1.34 4” Wide Polymer Concrete Trench Drain with Ductile Iron Edge and C Class, Ductile Iron Slotted Grate.
A. TD-50 CPS604-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: Supreme polymer channel with integrated cast iron edge designed to withstand
extreme loads. Equipped with special locking grates.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-Sloped][Flat].
3. Installation Brackets: [Yes][No].
4. Grate shall be C Class, Ductile Iron Slotted, with standard locks.
5. Drain shall include:
a. Standard grate hold down locks.
b. End Cap with outlet.
c. Solid End Cap.
1.35 4” Wide Polymer Concrete Trench Drain with Ductile Iron Edge and C Class, Heel Guard Grate.
A. TD-51 CPS604-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: Supreme polymer channel with integrated cast iron edge designed to withstand
extreme loads. Equipped with special locking grates.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-Sloped][Flat].
3. Installation Brackets: [Yes][No].
4. Grate shall be C Class, Heel Guard. ADA compliant, ductile iron with standard locks.
5. Drain shall include:
a. Standard grate hold down locks.
b. End Cap with outlet.
c. Solid End Cap.
1.36 4” Wide Polymer Concrete Trench Drain with Ductile Iron Edge and D Class, Ductile Iron, Slotted Grate.
A. TD-52 CPS604-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: Supreme polymer channel with integrated cast iron edge designed to withstand
extreme loads. Equipped with special locking grates.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-Sloped][Flat].
3. Installation Brackets: [Yes][No].
4. Grate shall be D Class, ductile iron, slotted with special locks.
5. Drain shall include:
a. Standard grate hold down locks.
b. End Cap with outlet.
c. Solid End Cap.
1.37 4” Wide Polymer Concrete Trench Drain with Ductile Iron Edge and F Class, Ductile Iron, Slotted Grate.
A. TD-53 CPS604-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: Supreme polymer channel with integrated cast iron edge designed to withstand
extreme loads. Equipped with special locking grates.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-Sloped][Flat].
3. Installation Brackets: [Yes][No].
4. Grate shall be F Class, ductile iron, slotted, with special locks.
5. Drain shall include:
a. Standard grate hold down locks.
b. End Cap with outlet.
c. Solid End Cap.
1.38 6” Wide Polymer Concrete Trench Drain with Ductile Iron Edge and C Class, Ductile Iron Slotted Grate.
A. TD-54 CPS606-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: Supreme polymer channel with integrated cast iron edge designed to withstand
extreme loads. Special locking grates.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Stepped][Flat].
3. Installation Brackets: [Yes][No].
4. Grate shall be C Class, ductile iron, slotted, with special locks.
5. Drain shall include:
a. End Cap with outlet.
b. Solid End Cap.
1.39 6” Wide Polymer Concrete Trench Drain with Ductile Iron Edge and C Class, Ductile Iron, 4 point lock,
Slotted Grate.
A. TD-55 CPS606-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: Supreme polymer channel with integrated cast iron edge designed to withstand
extreme loads. Special locking grates.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Stepped][Flat].
3. Installation Brackets: [Yes][No].
4. Grate shall be C Class, ductile iron, slotted, with 4 point lock.
5. Drain shall include:
a. End Cap with outlet.
b. Solid End Cap.
1.40 6” Wide Polymer Concrete Trench Drain with Ductile Iron Edge and F Class, Ductile Iron Slotted Grate.
A. TD-56 CPS606-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: Supreme polymer channel with integrated cast iron edge designed to withstand
extreme loads. Special locking grates.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Stepped][Flat].
3. Installation Brackets: [Yes][No].
4. Grate shall be F Class, ductile iron, slotted, with special locks.
5. Drain shall include:
a. End Cap with outlet.
b. Solid End Cap.
1.41 6” Wide Polymer Concrete Trench Drain with Ductile Iron Edge and D Class, Solid Cover.
A. TD-57 CPS606-[3, 6, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: Supreme polymer channel with integrated cast iron edge designed to withstand
extreme loads. Special locking grates.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Stepped][Flat].
3. Installation Brackets: [Yes][No].
4. Grate shall be D Class, ductile iron, solid cover, with special locks.
5. Drain shall include:
a. End Cap with outlet.
b. Solid End Cap.
1.42 6” Wide HDPE Trench Drain with A Class, Galvanized Slotted Grate.
A. TD-58 CPZ886-[06, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 6" wide pre-sloped trench drainage system. High density polyethylene structural
composite drain channel with .75% bottom slope or flat. All sections are 80-inch modular lengths with
integral top frame, inter-locking ends and radiused bottom. Combination tie-down/leveling devices at 20-
inch intervals.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped][Flat].
3. Installation Brackets: Built in – included.
4. Grate shall be A Class, galvanized steel, slotted, with standard locks.
5. Drain shall include:
a. Two Solid End Caps.
b. End Cap with outlet.
c. Bottom outlet.
1.43 6” Wide HDPE Trench Drain with A Class, Galvanized Perforated, ADA compliant Grate.
A. TD-59 CPZ886-[06, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 6" wide pre-sloped trench drainage system. High density polyethylene structural
composite drain channel with .75% bottom slope or flat. All sections are 80-inch modular lengths with
integral top frame, inter-locking ends and radiused bottom. Combination tie-down/leveling devices at 20-
inch intervals.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped][Flat].
3. Installation Brackets: Built in – included.
4. Grate shall be A Class, galvanized steel, perforated, ADA compliant, with standard locks.
5. Drain shall include:
a. Two Solid End Caps.
b. End Cap with outlet.
c. Bottom outlet.
1.44 6” Wide HDPE Trench Drain with A Class, Galvanized Perforated, reversed punch ADA compliant Grate.
A. TD-60 CPZ886-[06, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 6" wide pre-sloped trench drainage system. High density polyethylene structural
composite drain channel with .75% bottom slope or flat. All sections are 80-inch modular lengths with
integral top frame, inter-locking ends and radiused bottom. Combination tie-down/leveling devices at 20-
inch intervals.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped][Flat].
3. Installation Brackets: Built in – included.
4. Grate shall be A Class, galvanized steel, perforated, reversed punch, ADA compliant, with standard
locks.
5. Drain shall include:
a. Two Solid End Caps.
b. End Cap with outlet.
c. Bottom outlet.
1.45 6” Wide Trench Drain with A Class, Heel Proof Polyethylene ADA compliant Grate.
A. TD-61 CPZ886-[06, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 6" wide pre-sloped trench drainage system. High density polyethylene structural
composite drain channel with .75% bottom slope or flat. All sections are 80-inch modular lengths with
integral top frame, inter-locking ends and radiused bottom. Combination tie-down/leveling devices at 20-
inch intervals.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped][Flat].
3. Installation Brackets: Built in – included.
4. Grate shall be A Class, heel proof, high density polyethylene, ADA compliant, slotted.
5. Drain shall include:
a. Two Solid End Caps.
b. End Cap with outlet.
c. Bottom outlet.
1.46 6” Wide HDPE Trench Drain with B Class, Reinforced Galvanized Slotted Grate.
A. TD-62 CPZ886-[06, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 6" wide pre-sloped trench drainage system. High density polyethylene structural
composite drain channel with .75% bottom slope or flat. All sections are 80-inch modular lengths with
integral top frame, inter-locking ends and radiused bottom. Combination tie-down/leveling devices at 20-
inch intervals.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped][Flat].
3. Installation Brackets: Built in – included.
4. Grate shall be B Class, reinforced galvanized steel, slotted with standard locks.
5. Drain shall include:
a. Two Solid End Caps.
b. End Cap with outlet.
c. Bottom outlet.
1.47 6” Wide HDPE Trench Drain with B Class, Reinforced Galvanized Perforated, ADA Compliant Grate.
A. TD-63 CPZ886-[06, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 6" wide pre-sloped trench drainage system. High density polyethylene structural
composite drain channel with .75% bottom slope or flat. All sections are 80-inch modular lengths with
integral top frame, inter-locking ends and radiused bottom. Combination tie-down/leveling devices at 20-
inch intervals.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped][Flat].
3. Installation Brackets: Built in – included.
4. Grate shall be B Class, reinforced galvanized steel, perforated, ADA compliant, with standard locks.
5. Drain shall include:
a. Two Solid End Caps.
b. End Cap with outlet.
c. Bottom outlet.
1.48 6” Wide HDPE Trench Drain with B Class, Ductile Iron, Heel Proof, Longitudinal Slotted, ADA
Compliant Grate.
A. TD-64 CPZ886-[06, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 6" wide pre-sloped trench drainage system. High density polyethylene structural
composite drain channel with .75% bottom slope or flat. All sections are 80-inch modular lengths with
integral top frame, inter-locking ends and radiused bottom. Combination tie-down/leveling devices at 20-
inch intervals.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped][Flat].
3. Installation Brackets: Built in – included.
4. Grate shall be B Class, ductile iron, heel proof, Longitudinal Slotted, ADA Compliant with standard
locks.
5. Drain shall include:
a. Two Solid End Caps.
b. End Cap with outlet.
c. Bottom outlet.
1.49 6” Wide HDPE Trench Drain with C Class, Ductile Iron, Slotted Grate.
A. TD-65 CPZ886-[06, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80, 83,
86, 90, 93, 96, 99] [FT]: 6" wide pre-sloped trench drainage system. High density polyethylene structural
composite drain channel with .75% bottom slope or flat. All sections are 80-inch modular lengths with
integral top frame, inter-locking ends and radiused bottom. Combination tie-down/leveling devices at 20-
inch intervals.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped][Flat].
3. Installation Brackets: Built in – included.
4. Grate shall be C Class, ductile iron, slotted, with standard locks.
5. Drain shall include:
a. Two Solid End Caps.
b. End Cap with outlet.
c. Bottom outlet.
1.50 12” Wide HDPE Trench Drain with C Class, Ductile Iron, Slotted Grate.
A. TD-66 CPZ882-[08, 12, 16, 20, 24, 28, 32, 36, 40, 44, 48, 52, 56, 60, 64, 68, 72, 76, 80, 84, 88, 92, 96]
[FT]: 12” wide reveal trench drain system with stainless steel frame. Modular channel sections are made of
0% water absorbent high density polyethylene. Channels weigh less than 5.05 lb. and have radiused self-
cleaning bottom.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped][Flat].
3. Installation Brackets: Built in – included.
4. Grate shall be C Class, ductile iron, slotted, with standard 4 point locks.
5. Drain shall include:
a. Two Solid End Caps.
b. End Cap with outlet.
c. Bottom outlet.
1.51 12” Wide HDPE Trench Drain with E Class, Ductile Iron, Slotted Grate.
A. TD-67 CPZ882-[08, 12, 16, 20, 24, 28, 32, 36, 40, 44, 48, 52, 56, 60, 64, 68, 72, 76, 80, 84, 88, 92, 96]
[FT]: 12” wide reveal trench drain system with stainless steel frame. Modular channel sections are made of
0% water absorbent high density polyethylene. Channels weigh less than 5.05 lb. and have radiused self-
cleaning bottom.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped][Flat].
3. Installation Brackets: Built in – included.
4. Grate shall be E Class, ductile iron, slotted, with standard 4 point locks.
5. Drain shall include:
a. Two Solid End Caps.
b. End Cap with outlet.
c. Bottom outlet.
1.52 12” Wide HDPE Trench Drain with B Class, Heel Proof, ADA Compliant Ductile Iron Longitudinal,
Slotted Grate.
A. TD-68 CPZ882-[08, 12, 16, 20, 24, 28, 32, 36, 40, 44, 48, 52, 56, 60, 64, 68, 72, 76, 80, 84, 88, 92, 96]
[FT]: 12” wide reveal trench drain system with stainless steel frame. Modular channel sections are made of
0% water absorbent high density polyethylene. Channels weigh less than 5.05 lb. and have radiused self-
cleaning bottom.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped][Flat].
3. Installation Brackets: Built in – included.
4. Grate shall be B Class, Heel Proof, ADA compliant, ductile Iron, longitudinal slotted with standard
locks.
5. Drain shall include:
a. Two Solid End Caps.
b. End Cap with outlet.
c. Bottom outlet.
1.53 12” Wide HDPE Trench Drain with E Class, Ductile Iron Solid Cover.
A. TD-69 CPZ882-[08, 12, 16, 20, 24, 28, 32, 36, 40, 44, 48, 52, 56, 60, 64, 68, 72, 76, 80, 84, 88, 92, 96]
[FT]: 12” wide reveal trench drain system with stainless steel frame. Modular channel sections are made of
0% water absorbent high density polyethylene. Channels weigh less than 5.05 lb. and have radiused self-
cleaning bottom.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped][Flat].
3. Installation Brackets: Built in – included.
4. Grate shall be E Class, ductile iron, solid, with standard 4 point locks.
5. Drain shall include:
a. Two Solid End Caps.
b. End Cap with outlet.
c. Bottom outlet.
1.54 12” Wide HDPE Trench Drain with F Class, Ductile Iron Slotted Grate.
A. TD-70 CPZ882-[08, 12, 16, 20, 24, 28, 32, 36, 40, 44, 48, 52, 56, 60, 64, 68, 72, 76, 80, 84, 88, 92, 96]
[FT]: 12” wide reveal trench drain system with stainless steel frame. Modular channel sections are made of
0% water absorbent high density polyethylene. Channels weigh less than 5.05 lb. and have radiused self-
cleaning bottom.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped][Flat].
3. Installation Brackets: Built in – included.
4. Grate shall be F Class, ductile iron, slotted with standard 4 point locks.
5. Drain shall include:
a. Two Solid End Caps.
b. End Cap with outlet.
c. Bottom outlet.
1.55 6” Wide Shallow Polymer Concrete Trench Drain with A Class, Galvanized Steel, Slotted Grate.
A. TD-71 TPC500-[04, 08, 12, 16, 20, 24, 28, 32, 36, 40, 44, 48, 52, 56, 60, 64, 68, 72, 76, 80, 84, 88, 92, 96]
[FT]: This Series is deigned for instances where constraints such as vertical depth are more important than
hydraulics. With an overall depth of just 2.5" this trench drain fits the bill perfectly.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: Flat.
3. Installation Chairs: [Yes] [No].
4. 2 Foot Extension: [Yes] [No].
5. Grate shall be A Class, galvanized steel, slotted with standard locks.
6. Drain shall include:
a. Two Solid End Caps.
1.56 6” Wide Shallow Polymer Concrete Trench Drain with A Class, ADA Compliant, Longitudinal Plastic
(HDPE), Slotted Grate.
A. TD-72 TPC500-[04, 08, 12, 16, 20, 24, 28, 32, 36, 40, 44, 48, 52, 56, 60, 64, 68, 72, 76, 80, 84, 88, 92, 96]
[FT]: This Series is deigned for instances where constraints such as vertical depth are more important than
hydraulics. With an overall depth of just 2.5" this trench drain fits the bill perfectly.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: Flat.
3. Installation Chairs: [Yes] [No].
4. 2 Foot Extension: [Yes] [No].
5. Grate shall be A Class, ADA compliant, longitudinal slotted, high density polyethylene.
6. Drain shall include:
a. Two Solid End Caps.
1.57 6” Wide Shallow Polymer Concrete Trench Drain with C Class, Graye Iron, Slotted Grate.
A. TD-73 TPC500-[04, 08, 12, 16, 20, 24, 28, 32, 36, 40, 44, 48, 52, 56, 60, 64, 68, 72, 76, 80, 84, 88, 92, 96]
[FT]: This Series is deigned for instances where constraints such as vertical depth are more important than
hydraulics. With an overall depth of just 2.5" this trench drain fits the bill perfectly.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: Flat.
3. Installation Chairs: [Yes] [No].
4. 2 Foot Extension: [Yes] [No].
5. Grate shall be C Class, gray iron, slotted, with standard locks.
6. Drain shall include:
a. Two Solid End Caps.
1.58 6” Wide Shallow Polymer Concrete Trench Drain with E Class, Ductile Iron, Slotted Grate.
A. TD-74 TPC500-[04, 08, 12, 16, 20, 24, 28, 32, 36, 40, 44, 48, 52, 56, 60, 64, 68, 72, 76, 80, 84, 88, 92, 96]
[FT]: This Series is deigned for instances where constraints such as vertical depth are more important than
hydraulics. With an overall depth of just 2.5" this trench drain fits the bill perfectly.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped][Flat].
3. Installation Chairs: [Yes] [No].
4. 2 Foot Extension: [Yes] [No].
5. Grate shall be E class, ductile iron, slotted, with standard locks.
6. Drain shall include:
a. Two Solid End Caps.
1.59 6” Wide Shallow Polymer Concrete Trench Drain with E Class, ADA Compliant, Ductile Iron,
Longitudinal Slotted Grate.
A. TD-75 TPC500-[04, 08, 12, 16, 20, 24, 28, 32, 36, 40, 44, 48, 52, 56, 60, 64, 68, 72, 76, 80, 84, 88, 92, 96]
[FT]: This Series is deigned for instances where constraints such as vertical depth are more important than
hydraulics. With an overall depth of just 2.5" this trench drain fits the bill perfectly.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: Flat.
3. Installation Chairs: [Yes] [No].
4. 2 Foot Extension: [Yes] [No].
5. Grate shall be E Class, ADA compliant, ductile iron, longitudinal slotted, with standard locks.
6. Drain shall include:
a. Two Solid End Caps.
1.60 6” Wide Polymer Concrete Trench Drain with A Class, Galvanized Steel, Slotted Grate.
A. TD-76 TPC600-[04, 08, 12, 16, 20, 24, 28, 32, 36, 40, 44, 48, 52, 56, 60, 64, 68, 72, 76, 80, 84, 88, 92, 96]
[FT]: This Series is ideally suited for a variety of commercial and industrial applications. With the proper
components, flow rates of 470 GPM per outlet are attainable. The precast trench sections and grates are
made up of 2' and 4' lengths. Certain 4' channels and all half channels have 4" bottom cut-outs for pipe
connections.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped] [Flat].
3. Installation Chairs: [Yes] [No].
4. 2 Foot Extension: [Yes] [No].
5. Grate shall be A Class, galvanized steel, slotted.
6. Drain shall include:
a. One Solid End Caps or 4” inlet.
b. One Solid End Caps or 4” outlet.
c. Galvanized lockdowns
1.61 6” Wide Polymer Concrete Trench Drain with A Class, ADA Compliant, Longitudinal Slotted, Plastic
(HDPE), Grate.
A. TD-77 TPC600-[04, 08, 12, 16, 20, 24, 28, 32, 36, 40, 44, 48, 52, 56, 60, 64, 68, 72, 76, 80, 84, 88, 92, 96]
[FT]: This Series is ideally suited for a variety of commercial and industrial applications. With the proper
components, flow rates of 470 GPM per outlet are attainable. The precast trench sections and grates are
made up of 2' and 4' lengths. Certain 4' channels and all half channels have 4" bottom cut-outs for pipe
connections.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped] [Flat].
3. Installation Chairs: [Yes] [No].
4. 2 Foot Extension: [Yes] [No].
5. Grate shall be A Class, ADA compliant, longitudinal slotted, high density polyethyllene, Slotted,
with standard locks.
6. Drain shall include:
a. One Solid End Caps or 4” inlet.
b. One Solid End Caps or 4” outlet.
c. Galvanized lockdowns
1.62 6” Wide Polymer Concrete Trench Drain with C Class, Gray Iron, Slotted Grate.
A. TD-78 TPC600-[04, 08, 12, 16, 20, 24, 28, 32, 36, 40, 44, 48, 52, 56, 60, 64, 68, 72, 76, 80, 84, 88, 92, 96]
[FT]: This Series is ideally suited for a variety of commercial and industrial applications. With the proper
components, flow rates of 470 GPM per outlet are attainable. The precast trench sections and grates are
made up of 2' and 4' lengths. Certain 4' channels and all half channels have 4" bottom cut-outs for pipe
connections.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped] [Flat].
3. Installation Chairs: [Yes] [No].
4. 2 Foot Extension: [Yes] [No].
5. Grate shall be C Class, gray iron, slotted with standard locks.
6. Drain shall include:
a. One Solid End Caps or 4” inlet.
b. One Solid End Caps or 4” outlet.
c. Galvanized lockdowns
1.63 6” Wide Polymer Concrete Trench Drain with E Class, Ductile Iron, Slotted Grate.
A. TD-79 TPC600-[04, 08, 12, 16, 20, 24, 28, 32, 36, 40, 44, 48, 52, 56, 60, 64, 68, 72, 76, 80, 84, 88, 92, 96]
[FT]: This Series is ideally suited for a variety of commercial and industrial applications. With the proper
components, flow rates of 470 GPM per outlet are attainable. The precast trench sections and grates are
made up of 2' and 4' lengths. Certain 4' channels and all half channels have 4" bottom cut-outs for pipe
connections.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped] [Flat].
3. Installation Chairs: [Yes] [No].
4. 2 Foot Extension: [Yes] [No].
5. Grate shall be E Class, ductile iron, slotted, with standard locks.
6. Drain shall include:
a. One Solid End Caps or 4” inlet.
b. One Solid End Caps or 4” outlet.
c. Galvanized lockdowns
1.64 6” Wide Polymer Concrete Trench Drain with E Class, ADA Compliant, Ductile Iron, Longitudinal Slotted
Grate.
A. TD-80 TPC600-[04, 08, 12, 16, 20, 24, 28, 32, 36, 40, 44, 48, 52, 56, 60, 64, 68, 72, 76, 80, 84, 88, 92, 96]
[FT]: This Series is ideally suited for a variety of commercial and industrial applications. With the proper
components, flow rates of 470 GPM per outlet are attainable. The precast trench sections and grates are
made up of 2' and 4' lengths. Certain 4' channels and all half channels have 4" bottom cut-outs for pipe
connections.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped] [Flat].
3. Installation Chairs: [Yes] [No].
4. 2 Foot Extension: [Yes] [No].
5. Grate shall be E Class, ductile iron, ADA compliant, longitudinal slotted, with standard locks.
6. Drain shall include:
a. One Solid End Caps or 4” inlet.
b. One Solid End Caps or 4” outlet.
c. Galvanized lockdowns
1.65 6” Wide Polymer Concrete Trench Drain with C Class, Ductile Iron, Slotted Grate.
A. TD-81 TPC700-[04, 08, 12, 16, 20, 24, 28, 32, 36, 40, 44, 48, 52, 56, 60, 64, 68, 72, 76, 80, 84, 88, 92, 96,
99] [FT]: Whether exposed to hard wheel forklift traffic or aggressive chemicals, the 700 Series has the
solution. Based on TPC600 Series polymer concrete channels, the 700 Series is capable of flow rates of
470 GPM. The precast trench sections and grates are made up of 2' and 4' lengths. Certain 4' channels and
all half channels have 4" bottom cut-outs for pipe connections. The TPC700 is equipped with cast iron
frames protecting the edge of the channel for use in extreme conditions in industrial areas.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped] [Flat].
3. Installation Chairs: [Yes] [No].
4. 2 Foot Extension: [Yes] [No].
5. Grate shall be C Class, ductile iron, slotted, with standard locks.
6. Drain shall include:
a. One Solid End Caps or 4” inlet.
b. One Solid End Caps or 4” outlet.
c. Galvanized lockdowns
1.66 6” Wide Polymer Concrete Trench Drain with E Class, Ductile Iron, Slotted Grate.
A. TD-82 TPC700-[04, 08, 12, 16, 20, 24, 28, 32, 36, 40, 44, 48, 52, 56, 60, 64, 68, 72, 76, 80, 84, 88, 92, 96,
99] [FT]: Whether exposed to hard wheel forklift traffic or aggressive chemicals, the 700 Series has the
solution. Based on TPC600 Series polymer concrete channels, the 700 Series is capable of flow rates of
470 GPM. The precast trench sections and grates are made up of 2' and 4' lengths. Certain 4' channels and
all half channels have 4" bottom cut-outs for pipe connections. The TPC700 is equipped with cast iron
frames protecting the edge of the channel for use in extreme conditions in industrial areas.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped] [Flat].
3. Installation Chairs: [Yes] [No].
4. 2 Foot Extension: [Yes] [No].
5. Grate shall be E Class, ductile iron, slotted, with standard locks.
6. Drain shall include:
a. One Solid End Caps or 4” inlet.
b. One Solid End Caps or 4” outlet.
c. Galvanized lockdowns
1.67 6” Wide Polymer Concrete Trench Drain with E Class, ADA Compliant, Ductile Iron, Longitudinal Slotted
Grate.
A. TD-83 TPC700-[04, 08, 12, 16, 20, 24, 28, 32, 36, 40, 44, 48, 52, 56, 60, 64, 68, 72, 76, 80, 84, 88, 92, 96,
99] [FT]: Whether exposed to hard wheel forklift traffic or aggressive chemicals, the 700 Series has the
solution. Based on TPC600 Series polymer concrete channels, the 700 Series is capable of flow rates of
470 GPM. The precast trench sections and grates are made up of 2' and 4' lengths. Certain 4' channels and
all half channels have 4" bottom cut-outs for pipe connections. The TPC700 is equipped with cast iron
frames protecting the edge of the channel for use in extreme conditions in industrial areas.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped] [Flat].
3. Installation Chairs: [Yes] [No].
4. 2 Foot Extension: [Yes] [No].
5. Grate shall be E Class, ADA compliant, ductile iron, longitudinal slotted.
6. Drain shall include:
a. One Solid End Caps or 4” inlet.
b. One Solid End Caps or 4” outlet.
c. Galvanized lockdowns
1.68 6” Wide Polymer Concrete Trench Drain with Designer C Class. Ductile Iron (Specify Design) Grate.
A. TD-84 TPC700-[04, 08, 12, 16, 20, 24, 28, 32, 36, 40, 44, 48, 52, 56, 60, 64, 68, 72, 76, 80, 84, 88, 92, 96,
99] [FT]: Whether exposed to hard wheel forklift traffic or aggressive chemicals, the 700 Series has the
solution. Based on TPC600 Series polymer concrete channels, the 700 Series is capable of flow rates of
470 GPM. The precast trench sections and grates are made up of 2' and 4' lengths. Certain 4' channels and
all half channels have 4" bottom cut-outs for pipe connections. The TPC700 is equipped with cast iron
frames protecting the edge of the channel for use in extreme conditions in industrial areas.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped] [Flat].
3. Installation Chairs: [Yes] [No].
4. 2 Foot Extension: [Yes] [No].
5. Grate shall be Designer C Class, ductile iron, with standard locks.
6. Drain shall include:
a. One Solid End Caps or 4” inlet.
b. One Solid End Caps or 4” outlet.
c. Galvanized lockdowns
1.69 6” Wide Polymer Concrete Trench Drain with F Class, Gray Iron, Solid Cover.
A. TD-85 TPC700-[04, 08, 12, 16, 20, 24, 28, 32, 36, 40, 44, 48, 52, 56, 60, 64, 68, 72, 76, 80, 84, 88, 92, 96,
99] [FT]: Whether exposed to hard wheel forklift traffic or aggressive chemicals, the 700 Series has the
solution. Based on TPC600 Series polymer concrete channels, the 700 Series is capable of flow rates of
470 GPM. The precast trench sections and grates are made up of 2' and 4' lengths. Certain 4' channels and
all half channels have 4" bottom cut-outs for pipe connections. The TPC700 is equipped with cast iron
frames protecting the edge of the channel for use in extreme conditions in industrial areas.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped] [Flat].
3. Installation Chairs: [Yes] [No].
4. 2 Foot Extension: [Yes] [No].
5. Grate shall be F Class, ductile iron, solid, with standard locks.
6. Drain shall include:
a. One Solid End Caps or 4” inlet.
b. One Solid End Caps or 4” outlet.
c. Galvanized lockdowns
1.70 8” Wide Gel Coated Fiberglass Trench Drain with frame & C Class, Ductile Iron, Slotted Grate.
A. TD-86 TPC800-[08, 16, 24, 32, 40, 48, 56, 64, 72, 80, 88, 96] [FT]: The preformed trench drain shall be a
polyester matrix as shown on the contract plans. The frame clear opening dimension shall be 7.92“. The
channel widths shall be 8.25” with a full bottom radius. The frame shall fully support the grate and transfer
vertical loads linearly into adjacent concrete. Sloped and non-sloped channels shall be used as shown in
contract plans. Channels shall be 8' long. Sloped channels shall have a minimum 1% inverted slope.
Maximum capacity without extensions shall be 3700 GPM at flat and level grade. The channels shall
permit a continuously sloped run of 120' without extensions.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped] [Flat].
3. 4 Foot Extension: [Yes] [No].
4. Grate shall be C Class, ductile iron, slotted, supplied with bolts & washers.
5. Drain shall include:
a. Two Solid End Caps or 6” inlet. / outlet.
b. One 4”, 6”, or 8” bottom outlet.
1.71 8” Wide Gel Coated Fiberglass Trench Drain with frame & E Class, Ductile Iron, Slotted Grate.
A. TD-87 TPC800-[08, 16, 24, 32, 40, 48, 56, 64, 72, 80, 88, 96] [FT]: The preformed trench drain shall be a
polyester matrix as shown on the contract plans. The frame clear opening dimension shall be 7.92“. The
channel widths shall be 8.25” with a full bottom radius. The frame shall fully support the grate and transfer
vertical loads linearly into adjacent concrete. Sloped and non-sloped channels shall be used as shown in
contract plans. Channels shall be 8' long. Sloped channels shall have a minimum 1% inverted slope.
Maximum capacity without extensions shall be 3700 GPM at flat and level grade. The channels shall
permit a continuously sloped run of 120' without extensions.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped] [Flat].
3. 4 Foot Extension: [Yes] [No].
4. Grate shall be E Class, ductile iron, slotted, supplied with bolts & washers.
5. Drain shall include:
a. Two Solid End Caps or 6” inlet. / outlet.
b. One 4”, 6”, or 8” bottom outlet.
1.72 8” Wide Gel Coated Fiberglass Trench Drain with frame & E Class, ADA Compliant, Ductile Iron,
Longitudinal Slotted Grate.
A. TD-88 TPC800-[08, 16, 24, 32, 40, 48, 56, 64, 72, 80, 88, 96] [FT]: The preformed trench drain shall be a
polyester matrix as shown on the contract plans. The frame clear opening dimension shall be 7.92“. The
channel widths shall be 8.25” with a full bottom radius. The frame shall fully support the grate and transfer
vertical loads linearly into adjacent concrete. Sloped and non-sloped channels shall be used as shown in
contract plans. Channels shall be 8' long. Sloped channels shall have a minimum 1% inverted slope.
Maximum capacity without extensions shall be 3700 GPM at flat and level grade. The channels shall
permit a continuously sloped run of 120' without extensions.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped] [Flat].
3. 4 Foot Extension: [Yes] [No].
4. Grate shall be E Class, ductile iron, ADA compliant, longitudinal slotted, supplied with bolts &
washers.
5. Drain shall include:
a. Two Solid End Caps or 6” inlet. / outlet.
b. One 4”, 6”, or 8” bottom outlet.
1.73 8” Wide Gel Coated Fiberglass Trench Drain with frame & F Class, Ductile Iron, Slotted Grate.
A. TD-89 TPC800-[08, 16, 24, 32, 40, 48, 56, 64, 72, 80, 88, 96] [FT]: The preformed trench drain shall be a
polyester matrix as shown on the contract plans. The frame clear opening dimension shall be 7.92“. The
channel widths shall be 8.25” with a full bottom radius. The frame shall fully support the grate and transfer
vertical loads linearly into adjacent concrete. Sloped and non-sloped channels shall be used as shown in
contract plans. Channels shall be 8' long. Sloped channels shall have a minimum 1% inverted slope.
Maximum capacity without extensions shall be 3700 GPM at flat and level grade. The channels shall
permit a continuously sloped run of 120' without extensions.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped] [Flat].
3. 4 Foot Extension: [Yes] [No].
4. Grate shall be F Class, ductile iron, slotted, supplied with bolts & washers.
5. Drain shall include:
a. Two Solid End Caps or 6” inlet. / outlet.
b. One 4”, 6”, or 8” bottom outlet.
1.74 4" Wide with Galvanized Edge Fiber Reinforced Concrete, C class, ADA Compliant, Galvanized Steel,
Slotted Grates with Integral Locks.
A. TD-90 TOP100-[03, 06, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, S
83, 86, 90, 93, 96, 99] [FT]: Channels shall be 39.37” long, 6.22” wide reveal and have a 3.94” wide throat.
Modular channel sections shall be made of fiber-reinforced concrete. Shall have a male/female connection
between channel sections that will not separate during the installation. Channels shall have a radiused self-
cleaning bottom and 0.5% or neutral 0% built in slope. Channels shall have Galvanized Steel Edge Rails
built into the fiber-reinforced concrete. Channels shall have all grates locked down.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped] [Flat].
3. Grate shall be C class, ADA compliant, galvanized steel, slotted, with integral locks.
4. Drain shall include:
a. One Solid End Cap.
b. One outlet end cap.
1.75 4" Wide with Galvanized Edge Fiber Reinforced Concrete, C class, Reinforced Mesh Grates with Integral
Locks.
A. TD-91 TOP100-[03, 06, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80,
83, 86, 90, 93, 96, 99] [FT]: Channels shall be 39.37” long, 6.22” wide reveal and have a 3.94” wide throat.
Modular channel sections shall be made of fiber-reinforced concrete. Shall have a male/female connection
between channel sections that will not separate during the installation. Channels shall have a radiused self-
cleaning bottom and 0.5% or neutral 0% built in slope. Channels shall have Galvanized Steel Edge Rails
built into the fiber-reinforced concrete. Channels shall have all grates locked down.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped] [Flat].
3. Grate shall be C class, reinforced mesh, with integral locks.
4. Drain shall include:
a. One Solid End Cap.
b. One outlet end cap.
1.76 4" Wide with Galvanized Edge Fiber Reinforced Concrete, C Class, Ductile iron grates with integral locks.
A. TD-92 TOP100-[03, 06, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76, 80,
83, 86, 90, 93, 96, 99] [FT]: Channels shall be 39.37” long, 6.22” wide reveal and have a 3.94” wide throat.
Modular channel sections shall be made of fiber-reinforced concrete. Shall have a male/female connection
between channel sections that will not separate during the installation. Channels shall have a radiused self-
cleaning bottom and 0.5% or neutral 0% built in slope. Channels shall have Galvanized Steel Edge Rails
built into the fiber-reinforced concrete. Channels shall have all grates locked down.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped] [Flat].
3. Grate shall be C class, ductile iron, with integral locks.
4. Drain shall include:
a. One Solid End Cap.
b. One outlet end cap.
1.77 4" Wide with Ductile Iron Edge Fiber Reinforced Concrete, C class, ductile iron slotted grates with integral
locks.
A. TD-93 MAX100-[03, 06, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76,
80, 83, 86, 90, 93, 96, 99] [FT]: Channels shall be 39.37” long, 6.22” wide reveal and have a 3.94” wide
throat. Modular channel sections shall be made of fiber-reinforced concrete. Shall have a male/female
connection between channel sections that will not separate during the installation. Channels shall have a
radiused self-cleaning bottom and 0.5% or neutral 0% built in slope. Channels shall have Ductile Iron Edge
Rails built into the fiber-reinforced concrete. Channels shall have all grates locked down.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped] [Flat].
3. Grate shall be C class, ductile iron slotted with integral locks.
4. Drain shall include:
a. One Solid End Cap.
b. One outlet end cap.
1.78 4" Wide with Ductile Iron Edge Fiber Reinforced Concrete, D class, ductile iron slotted grates with integral
locks.
A. TD-94 MAX100-[03, 06, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76,
80, 83, 86, 90, 93, 96, 99] [FT]: Channels shall be 39.37” long, 6.22” wide reveal and have a 3.94” wide
throat. Modular channel sections shall be made of fiber-reinforced concrete. Shall have a male/female
connection between channel sections that will not separate during the installation. Channels shall have a
radiused self-cleaning bottom and 0.5% or neutral 0% built in slope. Channels shall have Ductile Iron Edge
Rails built into the fiber-reinforced concrete. Channels shall have all grates locked down.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped] [Flat].
3. Grate shall be D class, ductile iron slotted with integral locks.
4. Drain shall include:
a. One Solid End Cap.
b. One outlet end cap.
1.79 4" Wide with Ductile Iron Edge Fiber Reinforced Concrete, F class, ductile iron longitudinal slotted grates
with integral locks.
A. TD-95 MAX100-[03, 06, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76,
80, 83, 86, 90, 93, 96, 99] [FT]: Channels shall be 39.37” long, 6.22” wide reveal and have a 3.94” wide
throat. Modular channel sections shall be made of fiber-reinforced concrete. Shall have a male/female
connection between channel sections that will not separate during the installation. Channels shall have a
radiused self-cleaning bottom and 0.5% or neutral 0% built in slope. Channels shall have Ductile Iron Edge
Rails built into the fiber-reinforced concrete. Channels shall have all grates locked down.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped] [Flat].
3. Grate shall be F class, ductile iron longitudinal slotted with integral locks.
4. Drain shall include:
a. One Solid End Cap.
b. One outlet end cap.
1.80 6" Wide with Ductile Iron Edge Fiber Reinforced Concrete, D class, ductile iron slotted grates with integral
locks.
A. TD-96 MAX150-[03, 06, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76,
80, 83, 86, 90, 93, 96, 99] [FT]: Channels shall be 39.37” long, 6.22” wide reveal and have a 3.94” wide
throat. Modular channel sections shall be made of fiber-reinforced concrete. Shall have a male/female
connection between channel sections that will not separate during the installation. Channels shall have a
radiused self-cleaning bottom and 0.5% or neutral 0% built in slope. Channels shall have Ductile Iron Edge
Rails built into the fiber-reinforced concrete. Channels shall have all grates locked down.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped] [Flat].
3. Grate shall be D class, ductile iron slotted with integral locks.
4. Drain shall include:
a. One Solid End Cap.
b. One outlet end cap.
1.81 6" Wide with Ductile Iron Edge Fiber Reinforced Concrete, F class, ductile iron slotted grates with integral
locks.
A. TD-97 MAX150-[03, 06, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76,
80, 83, 86, 90, 93, 96, 99] [FT]: Channels shall be 39.37” long, 6.22” wide reveal and have a 3.94” wide
throat. Modular channel sections shall be made of fiber-reinforced concrete. Shall have a male/female
connection between channel sections that will not separate during the installation. Channels shall have a
radiused self-cleaning bottom and 0.5% or neutral 0% built in slope. Channels shall have Ductile Iron Edge
Rails built into the fiber-reinforced concrete. Channels shall have all grates locked down.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped] [Flat].
3. Grate shall be F class, ductile iron slotted with integral locks.
4. Drain shall include:
a. One Solid End Cap.
b. One outlet end cap.
1.82 6" Wide with Ductile Iron Edge Fiber Reinforced Concrete, E class, ductile iron mesh.
A. TD-98 MAX150-[03, 06, 10, 13, 16, 20, 23, 26, 30, 33, 36, 40, 43, 46, 50, 53, 56, 60, 63, 66, 70, 73, 76,
80, 83, 86, 90, 93, 96, 99] [FT]: Channels shall be 39.37” long, 6.22” wide reveal and have a 3.94” wide
throat. Modular channel sections shall be made of fiber-reinforced concrete. Shall have a male/female
connection between channel sections that will not separate during the installation. Channels shall have a
radiused self-cleaning bottom and 0.5% or neutral 0% built in slope. Channels shall have Ductile Iron Edge
Rails built into the fiber-reinforced concrete. Channels shall have all grates locked down.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Trench Drain Supply #
indicated.
2. Fall: [Pre-sloped] [Flat].
3. Grate shall be E class, ductile iron mesh with integral locks.
4. Drain shall include:
a. One Solid End Cap.
b. One outlet end cap.
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
Promo